Xex Menu Xbox 360

• How To Install Xex Menu Xbox 360

Apr 6, 2013 - This is XeX Menu 1.2 the most recent XeX Menu with this xex menu it has more skins and you can do some more. Category: Xbox 360 Other. RGH xbox 360 on latest dash with xex menu 1.2, dash launch 3.18.1,and. Xbox 360 RGH White 320gb BLUE LED's starwars sonus sound UPDATED. Currently unavailable. 3.3 out of 5 stars 3. ConsoleTuner Titan One for PS4, Xbox One, PS3 and Xbox 360 Oct 24, 2014. By ConsoleTuner. Where can I get used games for Xbox 360? Does the Xbox 1 play Xbox 360 games? Where can I download pirated games for Xbox 360?

How To Install Xex Menu Xbox 360

If you want to hack your Xbox 360 and your dashboard version is over 7371 then the only way that you can hack it is with the reset glitch hack (RGH). When I started looking for a way to hack my 360 I heard about the jtag method only to find out that my dashboard was newer then 7371, but in early September a hardware exploit was developed know as the RGH. Basically what the RGH does is send a single to the processor that tells it to reset. Usually it would do exactly that however if the single is sent when it is booting up it allows us to run unsigned code. To perform this RGH and utilize the exploit what you will need to do is read the NAND, install the modchip, write the NAND and installing your dash board of choice (i will be using xexmenu). To do this you will need: modchip (i will be using the coolrunner from team-xecuter) coolrunner LPT program cable male LPT port (printer cable) (x1) wires (x12 this will be your LPT cable so make them long) computer with a female LPT port a program to read the NAND (i used nandprob 2 you can find it ) soldering iron solder Jtag tool (software) 360gcprog (software) flux (not needed but HIGHLY recommended).Disclaimer: I am not liable for any damage that may be caused to your property or self from following the instructions in this tutorial.

Soldering irons can be very hot and cause burns, as well as possibly break your Xbox 360. Opening your xbox 360's shell will void its warranty. now then lets get started. First you need to completely take apart you 360 there are plenty of guides to do that so i wont cover it here.

When the case is removed it should look like the picture. I highly suggest that you take off the metal case it sits in so that you can access the bottom of the motherboard. To read the NAND, which is basically the Boot Sector of the Xbox 360, you will need to solder cables to the motherboard in very specific spots.

To find those points use the diagram in the first pictures, make sure you find it on the xbox, and flip the motherboard upside down making sure you can see the bottom of the points that you are going to solder to. I suggest flipping the motherboard upside down because the points are small bumps of solder removing any need to add external solder. I also put the resistor leg on the motherboard because they were easier to solder in to place. So if your soldering connections are strong and not overlapping anywhere then we are ready to read the NAND.

Open and install nandprob and restart your computer. After it has booted up again, open cmd and navigate to where the nandprob 2.0 folder is found and enter into the folder after you are inside type in (nandpro.exe lpt: -r16 nand1.bin) without the brackets. After the first one is done hit the up arrow key and change the nand1.bin part of the command to nand2.bin and dump the nand again. DUMPING MORE THEN ONCE IS VERY VERY IMPORTANT. Once you are done dumping all the times you want compare the files with total commander.you NEED to have two or more matching dumps before moving on.

It is alright to have 1 or 2 bad blocks in the NAND just so long as all the dumps are the same. If you have a slim skip this step to make sure that your xbox is exploitable the you need to know the CB version. Check the number in the 2BL CB field. The CB needs to be one of the following to be exploitable.

Zephyr: 4578, 4579 Falcon and Opus: 5771 Jasper: 6750, 6751 If the CB is not one of the numbers above, the console is not covered in this guide. Since writing this an new exploit call RGH 2.0 has made all phat Xboxs hackable was been released, However I have not had any experience with it. Attachments.

Now come the fun part! You get to solder the cool-runner into the actual 360. If you can't solder small points now would be the time to get someone else to do this for you. The first picture is a complete over view and the ones after that are of my personal install. The wires of the coolrunner are pre-tinned and cut to the perfect length for optimum glitch time (how long it takes to boot up). i would suggest just putting small amounts of flux on the wires and the motherboard, then touching the wire down and applying the soldering iron until the solder on the wire melts into place.

Ok so now that you have freeboot installed you can start up your xbox and if it boots then everything is good so you can unsolder the nand cable and pack up your xbox back in the case and put it where it would normally go, everything will be done with usb from now on. You need to get a usb stick and format it with the xbox. Download the program i have uploaded and go for the files for xex menu. Open up the program you downloaded and follow the images. Note: your xbox will not boot to xexmenu you will still have to go though the MS dashboard and launch it.

Although it is possible to make it so it will boot to it i am not including the instructions in this 'able. Attachments. Okay so you have an iso that you.ahem. Made and you want to play it.

It is actually very simple to do. Just go and download the program. Extract that sucker with 7-zip. once you have that done open it up and hit the choose iso folder button and select the folder your game is in. Choose a destination folder, make sure that your iso shows up and hit the go button. Once it is done extracting take all the files and transfer it to the xbox's harddrive or usb. Load up xexmenu and it should list your game right away.

Making three dumps is the minimum required to reconstruct a dump IF you have any read errors. I suggest you work on your soldering skills as I have personally never had issues dumping, but then again I have a background in electronics. If your dump takes A LONG time to complete AND you get differences on different spots. A shorten the wires and redo soldering spots.

The best tip I can give you is to heat up the spot you are going to solder for a second or to, then apply some tin and remove the tin and iron. You always want to preheat the spot to solder on to to make the tin melt and then apply just a tiny speck extra to merge it with the tin on the wire you want to solder. I never use flux on solder spots like these, the tin you use is likely to have a resin (flux) core. When reading nand you could have wrote that the xbox needs to have power on it, but not turned on. I tried reading the nand on two different computers.

The one computer had bad blocks each time and i think i tried all bios setups. The other computer was running ECP mode in bios on the lpt cable. And that gave me the best reading. It remapped a little bit of the nand but it worked great. (I used XNandHealer to verify the nands) On some computers when reading the nand the xbox may turn on by it self. Either in the beggining of the reading or the end but will most likely turn it self off again. Thiruttuvcd tamil movies online free. And for writing the nand.

You could have added text to see what pictures are from the xbox and maybe a little text that describes what you are about to do. Had to look at other guides to figure out how to get it working. And for the coolrunner LPT cable i used another schematic that was more simple. And i have also played with the settings menu in xexmenu. Pretty much all i done and now it runs all the games i had allready installed on the harddrive.?

What changed this you think? Is it the dashboard update or the settings thing in xexmenu? And last thing i run all the games from the normal game menu. Annabelle wallis. Xexmenu does not find any games?